60 lines
4.4 KiB
Markdown
60 lines
4.4 KiB
Markdown
# C64 SID instrument editor
|
|
|
|
the C64 instrument editor consists of two tabs: "C64" to control various parameters of sound channels, and "Macros" containing several macros.
|
|
|
|
## C64
|
|
|
|
- **Waveform**: allows selecting a waveform.
|
|
- more than one waveform can be selected at once. in that case a logical AND mix of waves will occur...
|
|
- due to hardware flaws, the mixing is a bit weird and sounds different between the 6581 and the 8580.
|
|
- noise is an exception. it cannot be used with any of the other waveforms.
|
|
- **Attack**: determines the rising time for the sound. the bigger the value, the slower the attack. (0 to 15).
|
|
- **Decay**: determines the diminishing time for the sound. the higher the value, the longer the decay (0 to 15).
|
|
- **Sustain**: sets the volume level at which the sound stops decaying and holds steady (0 to 15).
|
|
- **Release**: determines the rate at which the sound fades out after note off. the higher the value, the longer the release (0 to 15).
|
|
- **Duty**: specifies the width of a pulse wave (0 to 4095).
|
|
- **Ring Modulation**: when enabled, the channel's output will be multiplied with the previous channel's.
|
|
- **Oscillator Sync**: enables oscillator hard sync. as the previous channel's oscillator finishes a cycle, it resets the period of the channel's oscillator, forcing the latter to have the same base frequency. this can produce a harmonically rich sound, the timbre of which can be altered by varying the synchronized oscillator's frequency.
|
|
|
|
- **Enable filter**: when enabled, this instrument will go through the filter.
|
|
- **Initialize filter**: initializes the filter with the specified parameters:
|
|
- **Cutoff**: the filter's point in where frequencies are cut off (0 to 2047).
|
|
- **Resonance**: amplifies or focuses on the cutoff frequency, creating a secondary peak forms and colors the original pitch (0 to 15).
|
|
- **Filter mode**: sets the filter mode. you may pick one or more of the following:
|
|
- **low**: a low-pass filter. the lower the cutoff, the darker the sound.
|
|
- **high**: a high-pass filter. higher cutoff values result in a less "bassy" sound.
|
|
- **band**: a band-pass filter. cutoff determines which part of the sound is heard (from bass to treble).
|
|
- **ch3off**: mutes channel 3 when enabled. not sure why is this part of the chip's design, but it is.
|
|
- multiple filter modes can be selected simultaneously. for example, selecting both "low" and "high" would combine the effects of both, resulting in a bandpass filter.
|
|
|
|
- **Absolute Cutoff Macro**: when enabled, the cutoff macro will go from 0 to 2047, and it will be absolute (in other words, control the cutoff directly rather than being relative).
|
|
- **Absolute Duty Macro**: when enabled, the duty macro will go from 0 to 4095.
|
|
- **Don't test before new note**: this option disables the one-tick hard reset and test bit before a new note.
|
|
|
|
## Macros
|
|
|
|
- **Volume**: volume sequence.
|
|
- warning: volume sequence is global! this means it controls the chip's volume and therefore affects all channels.
|
|
- **Arpeggio**: pitch sequence.
|
|
- **Duty**: pulse width sequence.
|
|
- **Waveform**: select the waveform used by instrument.
|
|
- **Pitch**: fine pitch.
|
|
- **Cutoff**: filter cutoff.
|
|
- **Filter mode**: select the filter mode.
|
|
- **Resonance**: filter resonance sequence.
|
|
- **Special**: ring and oscillator sync selector, as well as:
|
|
- **gate bit**:
|
|
- set (1): key on. if previous state was 0 it triggers envelope start/restart; if previous state was 1, it does nothing.
|
|
- reset (0): key off. if previous state was 1 it triggers envelope release; if previous state was 0, it does nothing.
|
|
- **test bit**:
|
|
- set (1): immediately mute channel
|
|
- if the channel is a source of ring mod and/or hard sync, those stop working until the bit is reset.
|
|
- reset (0): unmute channel and restore ring mod/hard sync.
|
|
- **Attack**: sets envelope attack speed.
|
|
- if you modify attack speed when the envelope is in attack phase it immediately changes.
|
|
- **Decay**: sets envelope decay speed.
|
|
- if you modify decay speed when envelope is in decay phase it immediately changes.
|
|
- **Sustain**: sets envelope sustain level.
|
|
- if you modify sustain level when envelope is in sustain phase it immediately changes, although you can only go down. for example, 9-to-8 and 8-to-8 both work, but 8-to-9 immediately mutes the channel.
|
|
- **Release**: sets envelope release speed.
|
|
- if you modify release speed when envelope is in release phase it immediately changes. |