effect list

most of the effect numbers are from ProTracker / FastTracker 2.

however, effects are continuous, which means you only need to type it once and then stop it with an effect value of 00 or no effect value at all.

volume

0Axy: Volume slide.
- If x is 0 then this is a slide down.
- If y is 0 then this is a slide up.
F8xx: Single tick volume slide up.
F9xx: Single tick volume slide down.
F3xx: Fine volume slide up. 64× slower than 0Axy.
F4xx: Fine volume slide down. 64× slower than 0Axy.
FAxy: Fast volume slide. 4× faster than 0Axy.
- If x is 0 then this is a slide down.
- If y is 0 then this is a slide up.
07xy: Tremolo. changes volume to be "wavy" with a sine LFO. x is the speed, while y is the depth.
- Tremolo is downward only.
- Maximum tremolo depth is -60 volume steps.

E5xx: Set pitch. 00 is -1 semitone, 80 is base pitch, FF is nearly +1 semitone.
01xx: Pitch slide up.
02xx: Pitch slide down.
F1xx: Single tick pitch slide up.
F2xx: Single tick pitch slide down.
03xx: Portamento. slides the current note's pitch to the specified note.
- A note must be present for this effect to work.
E1xy: Note slide up. x is the speed, while y is how many semitones to slide up.
E2xy: Note slide down. x is the speed, while y is how many semitones to slide down.
EAxx: Toggle legato. while on, notes instantly change the pitch of the currrently playing sound instead of starting it over.
00xy: Arpeggio. after using this effect the channel will rapidly switch between semitone values of note, note + x and note + y.
E0xx: Set arpeggio speed. this sets the number of ticks between arpeggio values.
04xy: Vibrato. changes pitch to be "wavy" with a sine LFO. x is the speed, while y is the depth.
- Maximum vibrato depth is ±1 semitone.
E3xx: Set vibrato direction. xx may be one of the following:
- 00: Up and down.
- 01: Up only.
- 02: Down only.
E4xx: Set vibrato range in 1/16th of a semitone.

not all chips support these effects.

08xy: Set panning. changes stereo volumes independently. x is the left channel and y is the right one.
88xy: Set rear panning. changes rear channel volumes independently. x is the rear left channel and y is the rear right one.
80xx: Set panning (linear). this effect behaves more like other trackers:
- 00 is left.
- 80 is center.
- FF is right.
81xx: Set volume of left channel (from 00 to FF).
82xx: Set volume of right channel (from 00 to FF).
89xx: Set volume of rear left channel (from 00 to FF).
8Axx: Set volume of rear right channel (from 00 to FF).

09xx: Set speed/groove. if no grooves are defined, this sets speed. If alternating speeds are active, this sets the first speed.
0Fxx: Set speed 2. during alternating speeds or a groove, this sets the second speed.
Cxxx: Set tick rate. changes tick rate to xxx Hz (ticks per second).
- xxx may be from 000 to 3ff.
F0xx: Set BPM. changes tick rate according to beats per minute.
0Bxx: Jump to order. this can be used to loop a song.
0Dxx: Jump to next pattern. this can be used to shorten the current order.
FFxx: Stop song. stops playback and ends the song.

0Cxx: Retrigger. repeats current note every xx ticks.
- This effect is not continuous; it must be entered on every row.
ECxx: Note cut. ends current note after xx ticks. For FM instruments, it's equivalent to a "key off".
EDxx: Note delay. delays note by x ticks.

9xxx: Set sample position. jumps current sample to position xxx \* 0x100.
- Not all chips support this effect.
EBxx: Set sample bank.
- Does not apply on Amiga.
EExx: Send external command.
- This effect is currently incomplete.
F5xx: Disable macro. see macro table at the end of this document for possible values.
F6xx: Enable macro.

the interpretation of duty, wave and extra macros depends on chip/instrument type: