furnace/doc/7-systems/ym2610b.md

# Taito Arcade/Yamaha YM2610B

YM2610B is basically YM2610 with 2 extra FM channels used at some 90s Taito arcade hardware.
it is backward compatible with the original chip.

# effects

- `10xy`: **set LFO parameters.**
  - `x` toggles the LFO.
  - `y` sets its speed.
- `11xx`: **set feedback of channel.**
- `12xx`: **set operator 1 level.**
- `13xx`: **set operator 2 level.**
- `14xx`: **set operator 3 level.**
- `15xx`: **set operator 4 level.**
- `16xy`: **set multiplier of operator.**
  - `x` is the operator (1-4).
  - `y` is the multiplier.
- `18xx`: **toggle extended channel 3 mode.**
  - 0 disables it and 1 enables it.
  - only in extended channel 3 chip.
- `19xx`: **set attack of all operators.**
- `1Axx`: **set attack of operator 1.**
- `1Bxx`: **set attack of operator 2.**
- `1Cxx`: **set attack of operator 3.**
- `1Dxx`: **set attack of operator 4.**
- `20xx`: **set SSG channel mode.**
  - `00`: square
  - `01`: noise
  - `02`: square and noise
  - `03`: nothing (apparently)
  - `04`: envelope and square
  - `05`: envelope and noise
  - `06`: envelope and square and noise
  - `07`: nothing
- `21xx`: **set noise frequency.** range is `00` to `1F`.
- `22xy`: **set envelope mode.**
  - `x` sets the envelope shape, which may be one of the following:
    - `0`:` \___` decay
    - `4`:` /___` attack once
    - `8`:` \\\\` saw
    - `9`:` \___` decay
    - `A`:` \/\/` inverse obelisco
    - `B`:` \¯¯¯` decay once
    - `C`:` ////` inverse saw
    - `D`:` /¯¯¯` attack
    - `E`:` /\/\` obelisco
    - `F`:` /___` attack once
  - if `y` is 1 then the envelope will affect this channel.
- `23xx`: **set envelope period low byte.**
- `24xx`: **set envelope period high byte.**
- `25xx`: **slide envelope period up.**
- `26xx`: **slide envelope period down.**
- `29xy`: **enable SSG auto-envelope mode.**
  - in this mode the envelope period is set to the channel's notes, multiplied by a fraction.
  - `x` is the numerator.
  - `y` is the denominator.
  - if `x` or `y` are 0 this will disable auto-envelope mode.
- `30xx`: **enable envelope hard reset.**
  - this works by inserting a quick release and tiny delay before a new note.
- `50xy`: **set AM of operator.**
  - `x` is the operator (1-4). a value of 0 means "all operators".
  - `y` determines whether AM is on.
- `51xy`: **set SL of operator.**
  - `x` is the operator (1-4). a value of 0 means "all operators".
  - `y` is the value.
- `52xy`: **set RR of operator.**
  - `x` is the operator (1-4). a value of 0 means "all operators".
  - `y` is the value.
- `53xy`: **set DT of operator.**
  - `x` is the operator (1-4). a value of 0 means "all operators".
  - `y` is the value:
    - `0`: +0
    - `1`: +1
    - `2`: +2
    - `3`: +3
    - `4`: -0
    - `5`: -3
    - `6`: -2
    - `7`: -1
- `54xy`: **set RS of operator.**
  - `x` is the operator (1-4). a value of 0 means "all operators".
  - `y` is the value.
- `55xy`: **set SSG-EG of operator.**
  - `x` is the operator (1-4). a value of 0 means "all operators".
  - `y` is the value (0-8).
    - values between 0 and 7 set SSG-EG.
    - value 8 disables it.
- `56xx`: **set DR of all operators.**
- `57xx`: **set DR of operator 1.**
- `58xx`: **set DR of operator 2.**
- `59xx`: **set DR of operator 3.**
- `5Axx`: **set DR of operator 4.**
- `5Bxx`: **set D2R/SR of all operators.**
- `5Cxx`: **set D2R/SR of operator 1.**
- `5Dxx`: **set D2R/SR of operator 2.**
- `5Exx`: **set D2R/SR of operator 3.**
- `5Fxx`: **set D2R/SR of operator 4.**